This guide is general information, not legal advice. Federal rules are summarized from 49 CFR 396.11 and 396.13; your state may have its own requirements. Check with your state transportation agency or the FMCSA for your specific vehicles.
What a DVIR is
A driver vehicle inspection report (DVIR) is a written or electronic record a driver completes about the condition of a vehicle they operated. Under the federal motor carrier safety regulations, a motor carrier must require its drivers to prepare a report at the completion of each day's work on each vehicle operated, covering at least these parts and accessories:
- Service brakes, including trailer brake connections
- Parking brake
- Steering mechanism
- Lighting devices and reflectors
- Tires
- Horn
- Windshield wipers
- Rear vision mirrors
- Coupling devices
- Wheels and rims
- Emergency equipment
The report identifies the vehicle and lists any defect or deficiency that would affect safe operation or lead to a mechanical breakdown. The driver signs it. Under the current federal rule, a driver does not have to prepare a report if no defect or deficiency was found or reported.
Does it apply to my trade fleet?
The federal DVIR rule applies to commercial motor vehicles operated by motor carriers. In general terms, that covers vehicles in interstate commerce with a gross vehicle weight rating or gross combination weight rating of 10,001 pounds or more, among other categories. Many service vans fall below that line. But some trade vehicles do not:
- Heavier pickups and work trucks, especially with service bodies
- Dump trucks used by landscaping and roofing crews
- Pickups towing equipment or material trailers, where the combined rating can exceed 10,001 pounds
The federal rule also excludes a motor carrier operating only one commercial motor vehicle. Intrastate operations follow state rules, which often adopt federal standards with their own variations. Even where a DVIR is not legally required, a simple daily check is a good habit: it is the cheapest way to catch a soft tire or a dead brake light before it becomes a roadside problem.
The DVIR cycle, step by step
- Before driving. Under 49 CFR 396.13, before driving a commercial vehicle the driver must be satisfied it is in safe operating condition, review the last DVIR, and sign it if defects were noted and the carrier certified repairs or that repairs were unnecessary.
- End of day. The driver prepares a report for each vehicle operated, listing any defects found or reported.
- Corrective action. Before the vehicle is operated again, the carrier must repair any listed defect likely to affect safe operation, and certify on the report that the defect was repaired or that repair is unnecessary.
- Record keeping. The carrier keeps the original DVIR, the certification of repairs, and the driver's certification of review for three months from the date the report was prepared.
Reports can be created and kept electronically, which is how many fleets handle them today with a phone app or a telematics system.
Where small fleets usually slip
- Defects with no follow-up. A technician notes a worn tire, but nobody books the replacement or certifies the repair, and the same note shows up for weeks.
- Missing records. Paper reports end up in a glovebox or a truck console instead of a file you can produce if asked.
- Trailers forgotten. The truck gets inspected but the trailer coupling, lights, and brakes do not.
- Unclear ownership. The driver assumes the office will handle it; the office assumes the driver will mention it.
A simple DVIR routine for a trade fleet
- Decide which of your vehicles are covered and write it down, vehicle by vehicle.
- Give drivers one simple form or app, with the required items listed.
- Route every reported defect to one person or team who books the repair.
- Close the loop: certify the repair (or that it was unnecessary) before the vehicle goes back out, and have the next driver review it.
- Keep records for at least the three-month federal retention period, in one place.
- Review defect trends monthly. The same issue on the same vehicle is a maintenance signal.
How Fleet Command can help
Fleet Command Group is an outsourced fleet management team for service businesses. We coordinate repairs and vendors so reported defects get booked and followed up, keep maintenance and renewal calendars for every vehicle, and include safety and compliance records in our Complete plan. You can see what each plan includes on our pricing page. To pair inspections with a solid maintenance plan, read our preventive maintenance schedule for service vans.
If you run trucks for a landscaping, roofing, HVAC, plumbing, or electrical business, a free fleet cost review is a good place to start.
